View AA150XN02_7783113.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

free datasheet http://
free datasheet http://
products specifi cation rev.no. mdps - aa 150xn02 - 01 - 0 1 -- revision status for products specification products name color tft - lcd type name aa 150xn02 checked rev. description rev.date prepared approved y.numano first first revision mar.16, ? 04 t.hatashita k.kobayashi free datasheet http://
( 1 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first for optrex corporation 15.0 ? xga technical specification aa150x n02 ( t - 51863d150 - fw - a - ab ) mitsubishi / mdti date: mar.16, ?0 4 free datasheet http://
( 2 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first contents no. item page -- cover 1 -- contents 2 1 overview 3 2 absolute maximum ratings 4 3 electric al characteristics 4, 5 , 6 4 interface pin connection 7, 8 5 interface timing 9, 10, 11 , 12, 13 6 block diagram 14 7 mechanical specification 15, 16 8 optical characteristics 1 7 , 18 9 reliability test condition 19 10 inspection standards 20 11 hand ling precautions for tft - lcd module 21, 22, 23 12 revision status 24 free datasheet http://
( 3 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 1. overview aa 150xn02 is 15.0? color tft - lcd (thin film transistor liquid crystal display) modules composed of lcd panel, driver ics, control circuit, and backlight unit. by applying 6 bit or 8 bit digital data, 1 024 768, 260k - color or 16. 7 m - color images are displayed on the 15.0 ? diagonal screen. input power voltages are 3.3 v for lcd driving. general specifications are summarized in the following table: item specification display area (mm) 304.1 (h) 228.1 (v ) (15.0 - inch diagonal ) number of dots 1024 3 (h) 768 (v) pixel pitch (mm) 0.297 (h) 0.297 (v) color pixel arrangement rgb vertical stripe display mode normally white tn number of color 260k ( 6 bit/color ?j 16. 7 m(8 bit/color ?j brightness 45 0 c d/m 2 ?i typ. ?j wide viewing angle technology optical compensation film viewing angle - 75 ~ 75 (h) - 60~50 ( v) surface treatment anti - glare and hard - coating 3h electrical interface lvds(6 bit/ 8 bit) optimum viewing angle(contrast ratio) 6 o ? clock mo dule size (mm) 3 26 .0 (w) 2 55.0 (h) 15.9 (d) module mass (g) 1 310 backlight unit ccfl, 4 - tubes, edge - light, replaceable characteristic value without any note is typical value . the lcd product described in this specification is designed and manufa ctured for the standard use in oa equipment and consumer products, such as computers, communication equipment, industrial robots, av equipment and so on. do not use the lcd product for the equipment that require the extreme high level of reliability, such as aerospace applications, submarine cables, nuclear power control systems and medical or other equipment for life support. mdt i assumes no responsibility for any damage resulting from the use of the lcd product in disre gard of the conditions and handling precautions in this specification. if customers intend to use the lcd product for the above items or other no standard items, please contact our sales persons in advance. free datasheet http://
( 4 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 2. absolute maximum ratings item symbol min. max. unit power supply voltage for l cd vcc 0 4.0 v logic input voltage vi - 0.3 vcc+0.3 v lamp voltage v l 0 2500 v rms lamp current il 0 10.0 marms lamp frequency fl -- 100 khz operation temperature (panel) note 1,2) t op (panel) - 1 0 60 c operation temperature (ambient) note 2) t op (ambient) - 1 0 60 c storage temperature note 2) t stg - 20 70 c [note] 1) measured at the center of active area and at the center of panel back surface 2) top,tstg 40 c : 90%rh max. without condensation top,tstg > 40 c : absolute humidity shall be less than the value of 90%rh at 40 c without c ondensation . 3. electrical characteristics (1) tft - lcd ambient temperature : ta = 25c item symbol min. typ. max. unit remarks power supply voltage s for lcd vcc 3.0 3.3 3.6 v *1) power supply current s for lcd icc -- 410 700 ma *2) permissive input ripple voltage vrp -- -- 100 mvp - p vcc = + 3.3 v *1) power and signals sequence: 0.5 t1 10 ms 0 t2 5 0 ms 0 < t3 50 m s 500 m s t4 200 ms t5 0 t 6 t1 t2 t3 d ata 0. 9 v cc 0. 9 v cc 0.1v cc vcc t 4 t 5 t 6 vl data : rgb data, dclk, hd, vd, dena 0.1 v cc 0.1 v cc lcd power supply logic signal backlight power supply free datasheet http://
( 5 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first vcc - dip conditions: 1) when 2.6 v vcc < 3.0 v , td 10 ms 2) when vcc < 2. 6 v vcc - dip conditions should also follow the power and signals sequence. td 2.6 v 3.0 v vcc *2) typical current condition: 64 - gray - bar - pattern(6 bit) 25 6 - gray - bar - pattern (8 bit) 768 line mode vcc = +3.3 v, f h = 48.4 khz, f v = 60 hz, f clk = 65 mhz (2) backlight ta = 25c item symbol min. typ. max. unit remarks lamp voltage vl -- 620 -- v rms il = 6. 5 ma rms lamp current il 3.5 6.5 8. 0 ma rms *1) *4) lamp frequency f l 40 -- 7 0 khz *2) 1 6 00 -- -- v rms ta = 0c starting lamp voltage vs 1 4 00 -- -- v rms ta = 25c lamp life time lt -- 50000 -- h *3) , il = 6.5 ma rms, continuou s operation *1) lamp current measurement method (the current meter is inserted in low voltage line.) ctl ctl cth cth ctl cth cth ctl lcd module a inverter power supply a a a *2) lamp frequency of inverter may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. therefore, please adjust lamp frequency, and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference. *3) lamp life time is defined as the time either when the brightne ss becomes 50% of the initial value, or when the starting lamp voltage does not meet the value speci fied in this table. free datasheet http://
( 6 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first *4) please use the inverter which has symmetrical current wave form as follows, the degree of unbalance: less than 10% the ratio of wav e height: less than 2 10% i ph i pl i p h : high side peak i pl : low side peak the degree of u n balance = | i ph - i pl | / irms 100(%) the ratio of wave height = i ph (or i pl ) / irms current wave form free datasheet http://
( 7 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 4. interface pin connection (1) cn 1 (interface signal) used connector : df14h - 20p - 1.25h(hirose) corresponding connector: df14 - 20s - 1.25c(hirose) f unction(isp 6 bit compatibility mode) pin no. symbol 6 bit input 8 bit input function(isp 8 bit compatibility mode) 1 vcc +3.3 v power supply ? 2 vcc +3.3 v power supply ? 3 gnd gnd ? 4 gnd gnd ? 5 link 0 - r0, r1, r2, r3, r4, r5, g0 r2, r3, r4, r5, r6, r7, g2 r0, r1, r2, r3, r4, r5, g0 6 link 0 + r0, r1, r2, r3, r4, r5, g0 r2, r3, r4, r5, r6, r7, g2 r0, r1, r2, r3, r4, r5, g0 7 gnd gnd ? 8 link 1 - g1, g2, g3, g4, g5, b0, b1 g3, g4, g5, g6, g7, b2, b3 g1, g2, g3, g4, g5, b0, b1 9 link 1 + g1, g2, g3, g4, g5, b0, b1 g3, g4, g5, g6, g7, b2, b3 g1, g2, g3, g4, g5, b0, b1 10 gnd gnd ? 11 link 2 - b2, b3, b4, b5, hd, vd, dena b4, b5, b6, b7, hd, vd, dena b2, b3, b4, b5, hd, vd, dena 12 link 2 + b2, b3, b4, b5, hd, vd, dena b4, b5, b6, b7, hd, vd, dena b2, b3, b4, b5, hd, vd, dena 13 gnd gnd ? 14 clkin - clock - ? 15 clkin+ clock + ? 16 gnd gnd ? 17 link3 - gnd r0, r1, g0, g1, b0, b1 r6, r7, g6, g7, b6, b7 18 link3+ gnd r0, r1, g0, g1, b0, b1 r6, r7, g6, g7, b6, b7 19 mode l=isp 6 bit compatibility mode h=isp 8 bit compatibility mode 20 sc reverse scan control ( l : normal , h : reverse ) ? *) the shielding case is connecte d with gnd. (2) cn 2,4 ( backlight ) backlight - side connector : bh s r - 02vs - 1(jst) inverter - side connector: sm02b - bhs s - 1 - tb pin no. symbol function 1, 2 cth vblh ?i high voltage ?j [note] vblh - vbll = vl ( 3 ) cn 3,5 ( backlight ) backlight - side connector : bhr - 02 vs - 1(jst) inverter - side connector: sm02 (4.0) b - bhs - 1 - tb pin no. symbol function 1, 2 ctl vbll ?i low voltage ?j [note] vblh - vbll = vl free datasheet http://
( 8 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first (4) isp data mapping a. isp 6 bit compatibility mode(6 bit input) clkin+/- link0+/- 1clk link1+/- link2+/- r1 g0 r5 r4 r3 r2 r0 g2 b1 b0 g5 g4 g3 g1 b3 dena vd hd b5 b4 b2 clkin+/- link0+/- 1clk link1+/- link2+/- link3+/- r3 g2 r7 r6 r5 r4 r2 g4 b3 b2 g7 g6 g5 g3 b5 dena vd hd b7 b6 b4 r1 b1 b0 g1 g0 r0 *) link3/link3- is at gnd level. b. isp 6 bit compatibility mode(8 bit input) clkin+/- link0+/- 1clk link1+/- link2+/- link3+/- r1 g0 r5 r4 r3 r2 r0 g2 b1 b0 g5 g4 g3 g1 b3 dena vd hd b5 b4 b2 r7 b7 b6 g7 g6 r6 c. isp 8 bit compatibility mode free datasheet http://
( 9 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 5. interface timing lvds transmitter input sign al (1) timing specifications item symbol min. typ. max. unit frequency f clk 50 65 80 mhz dclk period t clk 12.5 15.4 20 ns horizontal active time t ha 1024 1024 1024 t clk horizontal front porch t hfp 0 24 -- t clk lcd timing horizontal back porch t hbp 4 296 -- t clk vertical active time t va 768 768 768 t h dena vertical front porch t vfp 2 3 -- t h vertical back porch t vbp 1 35 -- t h frequency f h 42.4 48.4 60 khz period t h 16.6 20.7 23.6 m s hd low width t whl 1 136 - - t clk frequency f v 55 60 75 hz period t v 13.3 16.7 18.2 ms vd low width t wvl 5 6 -- t h [note] * 1 ) polarities of hd and vd are negative in this specification. *2) dena (data enable) should always be positive polarity as shown in the timing specification. * 3) dclk should appear during all invalid period, and hd should appear during invalid period of frame cycle. *4) lvds timing follows the timing specifications of lvds receiver ic: thc63lvdf84a(thine). *5) t va + t vfp + t vbp 1024 free datasheet http://
( 10 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first (2) timing chart a. horizontal timing chart dclk data (r ,g,b) 1 2 1 023 1 024 3 invalid data invalid data t ha t hfp t hbp t whl t h =1/f h first data last data dena hd 1 2 767 768 3 invalid data invalid data t wvl t vfp t vbp t v =1/f v line data vd dena hd t va b. vertical timing chart free datasheet http://
( 11 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first (3) color data assignment a. 6 bit input input data r data g data b data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 color msb lsb msb lsb msb lsb black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 r ed (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 basic blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 color cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red (1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 red (2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 green (1) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 green (2) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 green green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 blue (1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 blue (2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 blue blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 [ note] 1) definition of gray scale color (n) --- n indicates gray scale level. higher n means brighter level. 2) data 1:high, 0: low free datasheet http://
( 12 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first b. 8 bit input input data r data g data b data r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b 2 b1 b0 color msb lsb msb lsb msb lsb black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(25 5 ) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 basic green(25 5 ) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 color blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(1) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(2) 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(25 5 ) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 green(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 green green(25 5 ) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 blue(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 blue blue(25 5 ) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 [note] * 1) definition of gray scale color (n) --- n indicates gray scale level. higher n means brighter level. *2) data 1:high, 0: low free datasheet http://
( 13 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first (4) data mapping d( 1, 1) d( 2, 1) --- d( x, 1) --- d(1023, 1) d(1024, 1) d( 1, 2) d( 2, 2) --- d( x, 2) --- d(1023, 2) d(1024, 2) | | + | + | | d( 1, y) d( 2, y) --- d( x, y) --- d(1023, y) d(1024, y) | | + | + | | d( 1,767) d( 2,767) --- d( x,767) --- d(1023,767) d(1024,767) d( 1,768) d( 2,768) --- d( x,768 ) --- d(1023,768) d(1024,768) free datasheet http://
( 14 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 6. block diagram timing controller backlight source driver lcd panel 1024 x 3 x 768 gate driver voltage supply for gray levels and vcom dc/dc converter cn 4 backlight tft-lcd module backlight ccfl 1 2 cn 2 , 4 cn 5 cn 2 cn 3 cn 1 1 2 cn 3, 5 free datasheet http://
( 15 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 7. mechanical specifications (1)front side free datasheet http://
( 16 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first (2)rear side [note] we recommend you referring to the detailed drawing for your design. please contact our company sales representa tive when you need the detailed drawing. free datasheet http://
( 17 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 8. optical characteristics ta = 25c , vcc = 3.3 v, input signals: typ. values shown in section 5 item symbol condition min. typ. max. unit remarks contrast ratio cr q = f = 0 3 00 4 50 -- -- *1) *3) luminance normal lw q = f = 0 360 450 -- cd/m 2 *2) *3) uniformity d lw q = f = 0 -- -- 30 % *2) *3) response time tr q = f = 0 -- 6 -- ms *3) *4) tf q = f = 0 -- 19 -- ms *3) * 4 ) horizontal f cr 3 10 -- - 75 ~ 75 -- *3) viewing vertical q -- - 60 ~ 50 -- *3) angle horizontal f cr 3 5 -- - 80 ~ 80 -- *3) vertical q -- - 80 ~ 70 -- *3) image sticking tis 2 h -- -- 2 s * 5 ) red rx 0.575 0.605 0.635 ry 0.310 0.340 0.370 color green gx 0.281 0.31 1 0.341 coordinates gy q = f = 0 0.535 0.565 0.595 -- *3) blue bx 0.124 0.154 0.184 by 0.100 0.130 0.160 white wx 0.283 0.313 0.343 wy 0.299 0.329 0.359 [note] these items are measured using cs1000(minolta) for color coordinat es, ezcontrast(eldim) for viewing angle, and cs1000 or bm - 5a(topcon) for others under the dark room condition (no ambient light) after more than 30 minutes from turning on the lamp unless noted . condition: il = 6 . 5 ma rms , inverter frequency: 5 0 khz * 1) d efinition of contrast ratio cr=on(white) luminance / off(black) luminance : point 5 shown in a figure below * 2) definition of luminance and luminance uniformity lw=on (white) luminance : point 5 shown in a figure below d l w =[l w (max)/l w (min) - 1] 100 (1,1) 256 512 768 192 384 576 (1024,768) 2 4 5 3 1 measurement point free datasheet http://
( 18 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first * 3) definition of viewing angle( q , f ) * 4) definition of response time w h i t e 9 0 % 9 0 % 1 0 % 1 0 % b l a c k t f t r l u m i n a n c e * 5) image s ticking continuously display the test pattern shown in the figure below f or two - hours. then display a completely white screen. the previous image shall not persist more than two seconds at 25c. black lines white area cols 510-514 rows 382-386 test pattern for image sticking test free datasheet http://
( 19 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 9. reliability test condition (1) temperature and humidit y test item conditions high temperature 40c, 90% rh, 240 h high humidity operation (no condensation) high temperature operation 60c, 240 h low temperature operation - 10c, 240 h thermal shock (non - operation) between - 20c (1 h ) and 7 0c(1 h ), 5 cycles high temperature storage 70c, 240 h low temperature storage - 20c, 240 h (2) shock & vibration item conditions shock level: 980 m/s 2 (100 g ?j shock waveform: half sinusoidal wave, 2 ms (non - operation) number of shocks: one shock input in each d irection of three mutually perpendicular axes for a total of six shock inputs vibration level: 9.8 m/s 2 (1.0 g ?j zero to peak waveform: sinusoidal vibration frequency range: 5 to 500 hz (non - operation) frequency sweep rate: 0.5 octave /min duration: one sweep from 5 to 500 hz in each of three mutually perpendicular axis(each x,y,z axis: 1 hour, total 3 hours) (3) judgment standard the judgment of the above tests should be made as follow: pass: normal display image with n o obvious non - uniformity and no line defect. partial transformation of the module parts should be ignored. fail: no display image, obvious non - uniformity, or line defects. free datasheet http://
( 20 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 10. inspection standards inspection condition is as follows: viewing distance is a pproximately 35 cm. viewing angle is normal to the lcd panel. ambient temperature is approximately 25c. ambient light is from 300 to 500 lx. bright dot is defined as follows: visible through 5% transmission nd filter under the condition that black image ( color 0) is on the display. defect type limit 0.01 mm < w 0.05 mm l 10 mm n 4 0.01 mm < w 10 mm < l n = 0 scratch 0.05 mm < w n = 0 0. 2 mm < f 0.4 mm n 4 dent 0.4 mm < f n = 0 0. 2 mm < f 0. 4 mm n 5 black spot bubble 0. 4 mm < f n = 0 l 3 mm w 0.1 mm n 4 3 mm < l w 0.1 m m n = 0 visual defect lint 0.1 mm < w according to black spot bright dot n 5 dark dot n 5 total dot n 8 two adjacent dot bright dot 2 pairs dark dot 2 pairs three or more adjacent dot not allowed distance between def ects bright dot 3 15 mm dark dot 3 15 mm electrical defect line defect not allowed *1) w: width,l: length, f : diameter,n: number *2) definition of adjacent g r b r g b r g b g r b r g b r g b g r b r g b r g b defective dot adjacent dots the defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties. free datasheet http://
( 21 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 1 1 . handling precautions for tft - lcd module please pay attention to the followings in handling tft - lcd products; (1) assembly precaution a. please mount the lcd module by using mounting hole with a screw clamp ing torque less than 0.5 nm. please do not bend or wrench the lcd module in assembling. p lease do not drop, bend or twist the lcd module in handling. please mount the invertor circuit board by using mounting hole of rear side with a screw clamping torque l ess than 0.2 nm. b. please design display housing in accordance with the following guide lines. (a) housing case must be designed carefully so as not to put stresses on lcd all sides and not to wrench module. the stresses may cause non - uniformity even if t here is no non - uniformity statically. (b) keep sufficient clearance between lcd module back surface and housing when the lcd mod ule is mounted. approximately 1.0mm of the clearance in the design is recommended taking into account the tolerance of lcd modu le thickness and mounting structure height on the housing. (c) when some parts, such as, fpc cable and ferrite plate, are installed underneath the lcd module, still sufficient clearance is required, such as 0.5mm. this clearance is, especially, to be recon sidered when the additional parts are implemented for emi countermeasure. (d) design the inverter location and connector position carefully so as not to give stress to lamp cable, or not to interface the lcd module by the lamp cable. (e) keep sufficient cl earance between lcd module and the others parts, such as inverter and speaker so as not to interface the lcd module. approximately 1.0mm of the clearance in the design is recommended. c. please do not push or scratch lcd panel surface with anything hard. a nd do not soil lcd panel surface by touching with bare hands. (polarizer film, surface of lcd panel is easy to be flawed.) d. please do not press any parts on the rear side such as source tcp, gate tcp, control circuit board and fpcs during handling lcd mo dule. if pressing rear part is unavoidable, handle the lcd module with care not to damage them. e. please wipe off lcd panel surface with absorbent cotton or soft cloth in case of it being soiled. f. please wipe off drops of adhesives like saliva and water on lcd panel surface immediately. they might damage to cause panel surface variation and color change. g. please do not take a lcd module to pieces and reconstruct it. resolving and reconstructing mod ules may cause them not to work well. h. please do no t touch metal frames with bare hands and soiled gloves. a color change of the metal frames can happen during a long preservation of soiled lcd modules. i. please pay attention to handling lead wire of backlight so that it is not tugged in connecting free datasheet http://
( 22 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first with i nverter. j. please connect the metal frame of lcd module to gnd in order to minimize the effect of external noise and emi. k. be sure to connect the cables and the connectors correctly. (2) operating precautions a. please be sure to turn off the power supply before connecting and disconnecting signal input cable. b. please do not change variable resistance settings in lcd module. they are adjusted to the most suitable value. if they are changed, it might happen lcd does not satisfy the characteristics specification. c. lcd backlight takes longer time to become stable of radiation characteristics in low temperature than in room temperature. d. the interface signal speed is very high. please pay attention to transmission line design and other high spee d signal precautions to satisfy signal specification. e . a condensation might happen on the surface and inside of lcd module in case of sudden change of ambient temperature. f. please pay attention not to display the same pattern for very long time. image might stick on lcd. even if image sticking happens, it may disappear as the operation time proceeds. g. please obey the same safe instructions as ones being prepared for ordinary electronic products. (3) precautions with electrostatics a. this lcd modu le use cmos - ic on circuit board and tft - lcd panel, and so it is easy to be affected by electrostatics. please be careful with electrostatics by the way of your body connecting to the ground and so on. b. please remove protection film very slowly from the s urface of lcd module to prevent from electro statics occurrence. (4) storage precautions a. please do not leave the lcds in the environment of high humidity and high temperature such as 60c90% rh. b. please do not leave the lcds in the environment of lo w temperature; below - 20c. (5) safety precautions a. when you waste damaged or unnecessary lcds, it is recommended to crush lcds into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. free datasheet http://
( 23 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first b. if any liquid le aks out of a damaged glass cell and comes in contact with the hands, wash off thor oughly with soap and water. c . be sure to turn off the power supply when inserting or disconnecting the cable. d. inverter should be designed carefully so as not to keep wo rking in case of detecting over current or open circuit on the lamp. (6) others a. a strong incident light into lcd panel might cause display characteristics changing inferior because of polarizer film, color filter, and other materials becoming inferio r. please do not expose lcd module direct sunlight and strong uv rays. b. please pay attention to a panel side of lcd module not to contact with other materials in preserv ing it alone. c. for the packaging box, please pay attention to the followings; (a) packaging box and inner case for lcd are designed to protect the lcds from the damage or scratching during transportation. please do not open except picking lcds up from the box. (b) please do not pile them up more than 5 boxes. (they are not designed so. ) and please do not turn over. (c) please handle packaging box with care not to give them sudden shock and vibrations. and also please do not throw them up. (d) packaging box and inner case for lcds are made of cardboard. so please pay attention not to ge t them wet. (such like keeping them in high humidity or wet place can occur getting them wet.) free datasheet http://
( 24 / 24) mitsubishi / mdti confidential AA150XN02_02_01_first 12. revision status checked rev. description date prepared approved y.numano first first revision mar.16, ? 04 t.hatashita k.kobayashi free datasheet http://
mitsubishi / mdti confidential (1/5) aa150xn01_03_01_first aa150xn ?? packaging specification packaging specification 1. packaging box material: cardboard construction: see fig. 1 max. packaging number: 10 pcs. dimension: 488 (w) 395 (h) 361 (d)[mm] mass(including 10 modules): 17.4 kg label: labels are put on the box.(see fig. 2, 3, 4) fig. 1. illustration of packaging box structure top cover inner box outside box lcd free datasheet http://
mitsubishi / mdti confidential (2/5) aa150xn01_03_01_first { `` ?? `` `` `` `` ?? ?? ?? ?? `` `` ?? `` `` `` `` ?? ?? ?? ?? `` packaging number bar-code serial no. product name bar-code serial no. bar-code bar-code serial no. bar-code serial no. bar-code serial no. bar-code serial no. bar-code serial no. bar-code serial no. bar-code serial no. bar-code serial no. bar-code box no. mass bar-code shipping no. bar-code packaging no. products name bar-code shipping no. bar-code shipping no. bar-code shipper fig.2. label1 fig.3. label 2 fig. 4. label 3 fig. 4. label 3 fig.5 sample of label3 label 1 label 2 label 3 fig. 6. location of labels optrex tft - lcd aa150xn01 ????? t-51863d150-fw-a-aa p / o no. 123456789 c / s 001 of 005 made in japan 001 ? ja1bk4144 2001/11/15 consignee product name product name of consignee order no. box no. place of production bar-code shipping date free datasheet http://
mitsubishi / mdti confidential (3/5) aa150xn01_03_01_first 2. location of label on the packaging box labels are put on the box.(see fig.6) 3. packaging form of product each of lcd module is packed in anti-electrostatic bag(fig. 7) packed lcd module is put in the packaging box.(fig. 8) the packaging box accumulates maximum 10 modules. upper protector is put on the products and shut the box.(fig. 9) product in anti-elctrostatic bag (surface) fig. 7 lamp lead product in anti-elctrostatic bag inner box fig. 8 free datasheet http://
mitsubishi / mdti confidential (4/5) aa150xn01_03_01_first top cover inner box fig. 9 4. cautions of shipping & storage do not turn the packaging upside down while storage and transportation. the boxes should not be piled up more than 5. handle with care. keep off from rain & dew. keep off from direct sunlight exposure. please store under room temperature & low humidity in original packaging condition when they were shipped. keep other cautions described in handling manual. free datasheet http://
mitsubishi / mdti confidential (5/5) aa150xn01_03_01_first 5 } revision status checked rev. description date prepared approved y.numano first first revision mar.16,?04 t.hatashita k.kobayashi free datasheet http://
mitsubishi / md t i confidential ( 1 / 3 ) productlabele _01_e products number labeling forms products number label is constructed as below; warning lamp ?@ high voltage made in japan ?@ brand name, symbol ?a t-51512d121-fw-a-aa ?b aa1 21sk26 ?c abc1234567890 ?d 60100001 1 l ?e bar-code e158720 ?@ brand name, symbol ?a products name of optrex ?b products name ?c production key number (13 digits) ?d date code ( serial number, factory sign ) ?e bar-code of date code ?f ul file no. ?g production country ?f ?g ?@ brand name, symbol optrex ?a products name of optrex ex. t51512d121 - fw - a - aa ?b products name ex.1: aa121sk26 ex.2: aa150xa03 b ?c production key number (13digits) (id number for production control ) ?d date code ?i serial number, factory sign ?j ???????????????????? 12 345678 9 10 factory sign serial number on every production week (00001 ?` 99999) production week number(01 ?` 53 ) production year number ?i last 1 digit of ad year number ?j ?e date code is constructed by 9 digits as below; 1st digit ?f production year number ?i last 1 figure of ad year ?j 2nd ?` 3rd digit ?f production week number in a year ?i a year is div ided to 53 weeks from monday to saturday ?j 4th ?` 8th digit ?f serial number on every production weeks. ?i 00001 ?` 99999 ?j these are numbered in order according to production name. 9th ?` 10 th digit ?f factory sign ( on the module test process) ( 1 l: shisui factory line, 1 y: yachiyo sanyo industries line , 1w: cpt fab - 1, 1r: cpt fab - 2, 1u: cpt wujiang - lcm - 1, 1v:cpt wujiang - lcm - 2 ?j free datasheet http://
mitsubishi / md t i confidential ( 2 / 3 ) productlabele _01_e ?e bar - code( date code ) bar - code line for computer readi ng date code mentioned as above. ?f ul file no. adi: e158720, cpt: e194548 ?g production country adi: made in japan, cpt: made in taiwan free datasheet http://
mitsubishi / md t i confidential ( 3 / 3 ) productlabele _01_e revision status checked revision notice description rev.date prepared approved m.nishimura first first revision jan . 14 ,? 02 t.h atashita s.yachi m.nishimura a t - 51512 - d121j - fw - a - aa ? t - 51512d121 - fw - a - aa jun.20 ,? 02 t.hatashita s.yachi m.nishimura b mitsubishi/adi confidential ? mitsubishi/mdti confidential aug.22 ,? 02 t.hatashita s.yachi y.numano c ?c date code ad d: u: cpt wujiang - lcm apr.3, ? 03 t.hatashita k.kobayashi y.numano d ?c date code u: cpt wujiang - lcm ? cpt wujiang - lcm - 1 add: v: cpt wujiang - lcm - 2 mar.1, ? 04 t.hatashita k.kobayashi y.nu mano e ?d date code add: 10th digit mar.16, ? 04 t.hatashita k.kobayashi free datasheet http://
mitsubishi / mdti confidential (1/10) AA150XN02_06_first lamp unit for 15.0"xga (AA150XN02, 03, 04) ? ? ? ? ? ? ? ? aa-l5902174g01(top) aa-l5902175g01(bottom) technical specification mitsubishi / mdti date: mar.16,?04 free datasheet http://
mitsubishi / mdti confidential (2/10) AA150XN02_06_first contents no. item page -- cover 1 -- contents 2 1 application 3 2 mechanical specification 3 3 environmental conditions 3 4 absolute maximum ratings 3 5 electrical characteristics 3 6 optical characteristics 4 7 life time of the lamp unit 4 8 interface pin connection 4 9 drawing of outline dimentions 5 10 method of replacing the lamp unit 6, 7, 8, 9 11 revision status 10 free datasheet http://
mitsubishi / mdti confidential (3/10) AA150XN02_06_first 1. application this technical literature applies to the replaceable lamp unit that is the maintenance parts for 15.0?xga tft-lcd module industrial use(model name:aa150xn 0 2. mechanical characteristics item specification remarks outline dimension of reflector 324 ? 0.6 ? 0.1 ? 0.1(mm) except wire mass 22 ? 3(g)(max) with wire and connector lamp diameter 3. environmental conditions item operation non operation min max min max remarks ambient temperature -10 ? 60 ? -20 ? 70 ? no condensation top,tstg ? 4. absolute maximum ratings item symbol min max unit lamp current il 0 10.0 marms lamp voltage vs 0 2500 vrms lamp frequency fl 0 100 khz 5. electrical characteristics item symbol condition min typ max unit remarks lamp current il ta = inverter power supply a a a free datasheet http://
mitsubishi / mdti confidential (4/10) AA150XN02_06_first 6. optical characteristics (1,1) 256 512 768 192 384 576 (1024,768) 2 4 5 3 1 these items are measured when lamp units are assembled into AA150XN02, xn03 or xn04, and using cs1000(minolta) for color coordinates, and cs1000 or bm-5a(topcon) for luminance under the dark room condition (no ambient light) after more than 30 minutes from turning on the lamp unless noted. 7. life time of the lamp unit environmental conditions are as follows: ambient temperature is 25 ~ no flickers should be allowed. ~ decrease in luminous length that is caused by lamp blacking is within 11 mm from the edge of the lamp. free datasheet http://
mitsubishi / mdti confidential (5/10) AA150XN02_06_first 8. interface pin connection (1) backlight-side connector: bhsr-02vs-1(jst) inverter-side connector: sm02b-bhss-1-tb pin no. symbol function 1, 2 cth vblh high voltage ????? [note] vblh-vbll = vl (2) backlight-side connector: bhr-02vs-1(jst) inverter-side connector: sm02(4.0)b-bhs-1-tb pin no. symbol function 1, 2 ctl vbll low voltage [note] vblh-vbll = vl 9. drawing of outline dimentions (1)aa-l5902174g01(top) (2) aa-l5902175g01(bottom) free datasheet http://
mitsubishi / mdti confidential (6/10) AA150XN02_06_first 10. method of replacing the lamp unit ? (1) precautions please pay attention to the following items while replacing the lamp unit. a. please do not damage the lcd panel surface, and do not touch it with bare hands. (wearing gloves is recommended.) b. please be careful with electrostatics, and work in clean environment to prevent entering dust and/or foreign matters that will cause bad display image. c. please be careful of the edge of the frame metal. ? d. please replace top and bottom lamp units at the same time. replace only one lamp unit will cause inferior display image. ? (2) method of replacing the lamp unit 1) ? picture ? ? 2) turn the tft-lcd module upside down. ? ? ? ? ? ? ? ? ??????????????????????????????????? ??????????????????????????????????? ??????????????????????????????????? ????????????????????????????????????????????????? ?????????????? ?????????????? ??????????????? ? ? ? picture 2 < please check the rear surface for dust and foreign matters. bottom please check the lcd panel surface for scratch, dust, and foreign matters. top free datasheet http://
mitsubishi / mdti confidential (7/10) AA150XN02_06_first 3) stand the tft-lcd module up and push down the latch of rubber holder with that lamp unit fastens using a screw driver(-) and the like. ? ?????????? ? picture 3 ? ? ? ? ? 4) pull the low voltage side cable ?? ??????????????? ? picture 4 5) remove the other lamp unit at the opposite(bottom) side of lcd module in the same way. see.3) and 4) 6) picture 5 shows the tft-lcd module after removing the lamp units . ? picture 5 push down the latch o f rubber holder. free datasheet http://
mitsubishi / mdti confidential (8/10) AA150XN02_06_first 7) prepare to insert the new lamp units. ? ? ? 8) stand the tft-lcd module up and insert the new lamp unit. the light guide and reflector sheet should be inside of the lamp unit. please be careful not to hurt your hands from the edge of the lamp unit. please pay attention to insert direction. ??? ? picture 6 ? 9) please insert lamp unit. after inserting the lamp unit, please check that the lamp unit is ???????????????????????????? ? ?????????????? picture 7 please check that the lamp unit is fastened with the latch o f rubber holder. free datasheet http://
mitsubishi / mdti confidential (9/10) AA150XN02_06_first 10) put the lamp cables in the trench of the plastic frame to keep inside of the module. picture 8 11) insert the other lamp unit to the opposite(bottom) side of the lcd module in the same way. ? ? ? free datasheet http://
mitsubishi / mdti confidential (10/10) AA150XN02_06_first 11. revision status checked rev. notice description rev. date prepared approved y.numano first first revision mar.16,?04 t.hatashita k.kobayashi free datasheet http://

▲Up To Search▲

Price & Availability of AA150XN02

	To Download AA150XN02 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .